1‑800‑263‑2309 Dealer Portal →
Cold-Start Protection

Equipment that starts. Even at −37°.

TITAN silicone heater pads bond permanently to oil pans, hydraulic tanks, fuel filters and batteries — dependable starts on the coldest mornings, and protection from the damage cold does to engines, batteries and fuel systems.

The coldest mornings are the most expensive

A no-start on a rented machine is a service call, a credit and a lost rental day — and the cold starts that do succeed quietly wear down the engine, the battery and the fuel system. TITAN heater pads take both off the table.

Compact equipment lives outside. Skid steers, compact track loaders, mini excavators, generators and light towers sit on job sites and in yards overnight — and in a hard cold snap, cold-soaked oil and gelled diesel are the difference between a machine that earns and a machine that waits for a service truck.

The quieter cost is the damage. Most engine wear happens in the seconds after a cold start, before thickened oil reaches the bearings. Cold-soaking drains the battery's cranking power, and gelled diesel starves filters and injectors. Keeping the machine warm isn't a comfort feature — it protects the equity in every unit on the lot.

01

Fewer winter service calls

Every prevented no-start is a technician roll, a swap unit and an unhappy customer you never have to deal with.

02

Protect the machines that sit outside

CTLs, mini excavators, generators and light towers spend winter nights cold-soaked on site. A pad keeps them rental-ready.

03

Reduce engine wear and warranty claims

Warm oil at ignition means full lubrication from the first crank — less wear, fewer warranty conversations, stronger resale value.

04

Install once, zero maintenance

The 3M™ VHB bond is permanent and the pad has no moving parts. No re-application, no seasonal teardown, nothing to inspect.

05

An easy winter line item

Cold-weather kits attach naturally to every winter rental contract and compact equipment sale.

Woodbridge snowcat parked on a groomed alpine trail in the mountains

Three ways to stop cold starts

TITAN heater pads are flexible silicone heating elements that bond permanently to the machine and plug in overnight — no moving parts, nothing to maintain, rated to −37 °C (−35 °F).

Woodbridge supplies the full TITAN range — made since 1992 and trusted by defense contractors, OEMs and heavy-equipment operators. There's a heater for each failure point, or one kit that covers the whole machine.

TITAN engine and fluid heater pad

Engine & Fluid Heater Pads

Silicone pads for engine oil pans and hydraulic reservoirs — sized by fluid capacity, from 1-quart sumps to 100-gallon tanks.

50–1,000 W · 12V DC / 120V / 240V AC
Shop on padheaters.com
TITAN fuel filter heater

Fuel Filter Heaters

Wrap-around heaters that mount directly to the fuel filter, preventing diesel gelling and fuel-flow restriction at the source.

50–100 W · 12V / 24V DC
Shop on padheaters.com
TITAN battery warmer

Battery Warmers

Electric warmers that keep the battery itself from cold-soaking — preserving cranking power on trucks, generators and heavy equipment.

60 W · 120V / 240V AC
Shop on padheaters.com
The Complete Kit

All three at once: Cold Weather Protection Kits

Oil pan heater, battery warmer and a thermostat-controlled outlet that cycles them automatically — one plug per machine and the whole cold-start problem is handled.

Complete Kit · 120V AC
Shop on padheaters.com
TITAN cold weather protection kit on diamond plate steel
03 / How It Works

Industrial heat, bonded to the machine

Warm oil flows. Cold oil does not. Every TITAN pad is four layers of industrial heating pressed onto clean metal once and plugged in overnight — fluids reach working viscosity before ignition, so the engine starts under lubrication instead of against it.

01

Durable silicone outer layer

Flexible, weather-resistant protection built for demanding environments.

02

Precision-etched heating element

Engineered for consistent heat distribution across the entire pad.

03

Insulating silicone inner layer

Protects the element while directing heat into the mounting surface.

04

3M™ VHB adhesive backing

High-strength peel-and-stick adhesive for a secure, permanent bond.

Exploded view of TITAN heater pad construction: silicone outer layer, etched heating element, insulating inner layer and 3M VHB adhesive backing
Bond

Peel the liner and press the pad onto clean metal. Installed in minutes.

Plug In

Standard outlet, or hardwired on DC models. Add a thermostat outlet and it cycles itself.

Heat

Fluid reaches about 38 °C (100 °F) in under two hours — ready before the shift starts.

Start

Oil flows on the first crank. Full pressure, no warm-up, no wear.

Sized by fluid capacity, not engine model

Pick the pad by how much oil or hydraulic fluid it has to warm, and match the voltage to the power available. The full sizing chart lives at padheaters.com.

One machine

Order directly online at padheaters.com — the sizing tool matches a pad to your oil pan or tank and it ships to your door.

A fleet, or stock for resale

Send Woodbridge your model list and we'll come back with per-unit recommendations and dealer pricing.